RO Water Purifier not working? Well, you are not alone. This is one of the most commonly recurring problems often faced by the people who use the RO. While repairs and services are can be conducted regularly, it is important to identify the underlying problem. So, what can be the main reasons for the RO not working, and what are its precise solutions? Let us find out:
This is one of the most basic yet often overlooked reasons for the RO not working. Inadequate or faulty power supply. This could be the main power supply that can cause the appliance to not work properly or certain loose connections.
The Solution:
Get hold of a tester to check the main energy point for your RO. Also, taking a good look at the switchboard can help resolve many issues; this could include tripping cases. Any faulty connections and voltage fluctuations can be detected; likewise, these need to be rectified on time. The best bet is to get hold of a nice electrician to take a thorough look at your power supply and your appliance as well.
2. The Filters
RO Water Purifier is not working? Well, it could be something to do with the filters. This is mainly because some RO models comprise the Auto-Shutoff feature that tends to kick off once the filters clog up. This also indicates that it is time to change your filters, or they require some amount of cleaning up to do. Also, specific models have the ‘beep sound’ emerging as and when the RO requires its filters to be cleaned up.
The Solution:
Its, simple. Get hold of your service centre guy and get the filters replaced.
3. The Air Bubble
Sounds strange? Yes, there is a rare possibility that an ‘air bubble’ might get stuck within your RO system. This is mainly due to the inappropriate or loose fittings. This occurs when the pipes are not well-sealed during the time the machine is being installed. Due to this, a small pocket of air usually gets caught in between the tubes.
The Solution:
Do not attempt this by yourself, as you could do more harm than repair. For the Air Bubble problem, it is advised to contact an authorized service person who has the right knowledge of how to release the air bubble from within the tubes.
4. Decreased Water Pressure
Is your RO Water Purifier not working? Well, check the water pressure. Due to decreased pressure in the main water supply, the process of filtration is decreased. This causes the water to reach the filter system very slowly, causing a hindrance to the required water output. Over time, this can cause the process of filtration to stop completely, thus, bringing your RO to a complete un-explained halt.
The Solution:
Get the water pressure checked. Meanwhile, take a closer look at the various taps around the household.
5. The Floats
Did you know that the funny-looking float valves could cause massive mishaps in the working of the RO system? This is because the float valves work by shutting down the filtration process once the tank reaches its level. It also ensures that no amount of overflowing occurs during this process. However, if you discover that your RO has stopped working suddenly, this could be due to the malfunction of the float valve.
The Solution:
Check the float valve and replace it if found defective. Like the filters, the float valve also requires constant checking-ups and subsequent replacements if required.
Also Read:
6. The Solenoid Valve
This is yet another essential part of the RO water purifier. The main function of the Solenoid Valve is to avoid the wastewater from flowing back into the membrane once the system shuts down. Is RO Water Purifier stopped working? Well, this could be because the Solenoid Valve is damaged, and these need immediate attention.
The Solution:
You will need to replace the Solenoid Valves in this case.
7. The Pressure Pump
The pressure pump is the in-built pump that functions to ensure the smooth working of the RO system. It works by applying high pressure that allows the RO to work in the required manner. If in case you figure out that the machine is not working well or has stopped working altogether, it could be something to do with the pumps.
The Solution:
If you observe that the ‘whirring sound of the RO machine is not audible, you can conclude that the pumps are not working as they should. This requires immediate replacement of the Pressure pumps, and you are good to go.
8. The Feeder Valve
This is the valve that is fixed on to the main kitchen water supply. The main function of the Feeder valve is to supply water from the main source to the RO machine. There are times when the valve can be turned off by mistake, thus causing the machine to shut off automatically.
The Solution: Simply turn-On the Feeder valve to ensure the smooth functioning of the RO machine.
9. SMPS Adapter
This is perhaps one of the most important parts of a RO system. The SMPS adapter is responsible for the conversion of the Alternating Current to Direct Current, which is responsible for the normal functioning of the RO. If you find that your machine is not working, you need to look at the SMPS Adapter.
The Solution: In case you finally figure out that the main issue is with the SMPS adapter, it is time to replace it.
RO Water Purifier Not Working Suddenly?: The Conclusion
So, dear folks, these are among the most important Information to RO Water Purifier not working in the right manner. Most times, our machines are simply overworked and need some amount of attention. Be sure to service your RO from time to time and take care of the repairs and replacements. These small steps are vital for the smooth working of your RO system for years to come.